Pecan Valley Plumbing
Get help with Pinhole Leaks in Copper Pipe
Call Pecan Valley Plumbing, have us call you, or describe the issue.
Prefer to talk?
Call (512) 555-0147Small leaks in copper pipe caused by pitting from the inside, repaired as a single spot or addressed as a pattern across the whole run.
01Pinhole leaks
These are common signs that copper pipe has started pitting from the inside. On-site testing narrows the location before any repair begins.
Copper thins from the inside until it gives way at one small point — usually a pinprick-sized hole rather than a crack or split.
A second or third pinhole on the same run, even at a different spot each time, points to conditions affecting the whole length of pipe rather than one bad section.
A blue-green stain on copper, or on what's beneath it, is corrosion at the surface and often shows up before a pipe actually pinholes through.
02The real question
Both start the same way: a small hole in copper pipe. What decides the right fix is what conditions caused it.
One small hole in an otherwise young, correctly sized line, with no other leaks and no staining elsewhere, is often just a single weak point — a spot where the pipe was thin, nicked during installation, or sat against something that wore at it from outside. Repairing that one section is usually enough.
More than one pinhole, especially on the same run or at different spots over time, points to something acting on the whole line rather than one bad section — the water itself, how fast it moves, or copper that was undersized or thin-walled from the start. That is a different conversation than a single repair.
Pinhole Leaks in Copper Pipe
Serving Round Rock, TX.
03Why it happens
Copper does not usually fail all at once. Water moving through it — how aggressive it is chemically, how fast it travels, and how much dissolved oxygen it carries — slowly wears a thin spot on the inside of the pipe wall until that one point gives way. The same water and the same velocity are moving through the rest of the line the whole time, not just the part that failed first.
The pipe's own grade matters too. Thinner-walled copper, common in some installations, pits sooner than a heavier grade under the same conditions. So does its age: copper that has carried water for decades has had that much longer for the same slow wear to reach a weak point. None of that tells a plumber exactly where the next pinhole will be, only whether one is likely.
04Reading the signs
None of these decide it alone. Together, they're what a plumber weighs before recommending a spot repair or something larger.
Pinholing is a wear failure, and older copper has simply had more time exposed to the same water for the same wear to build up. A first pinhole on a line already decades old carries more weight than one on pipe installed a few years ago.
Water that is acidic, high in dissolved minerals, or otherwise aggressive toward copper wears the inside of the pipe faster than water closer to neutral. The water itself does not change between one section of pipe and the next, which is part of why a pattern tends to spread.
Pipe that is undersized for the fixtures it feeds, or that narrows sharply at a fitting, sees water moving faster than copper is built to handle at that point. That wear shows up first wherever the flow is roughest, not necessarily where the pipe is oldest.
05Questions
Copper corrodes from the inside when the water moving through it is more aggressive than the pipe can tolerate — acidic or mineral-heavy water, water moving faster than the pipe was sized for, or copper that was thin to begin with all wear a spot thin until it gives way. Whatever caused one pinhole is usually still present in the rest of the line.
Not necessarily. A single leak on an otherwise young, well-sized line can be just that — one weak point. But when the same conditions that caused it are still acting on the rest of the run, more leaks tend to follow, sometimes within months of the first. A plumber weighs the pipe's age, its grade, and where the first leak sat before deciding whether a spot repair is enough.
Not always. One isolated pinhole on a line that is otherwise sound is usually a straightforward spot repair. A pattern of leaks, or a line old enough and thin enough that more failures are expected, is a different conversation — one about replacing the run rather than patching it leak by leak.
Water that cannot be stopped, sewage coming up, no water at all, or a smell of gas: urgent. A drip, a slow drain or a running toilet: worth fixing soon, but not tonight. When in doubt, shut off the water to the fixture and ask.
If water is actively leaking, yes: the fixture’s own valve, or the main if it doesn’t have one. A slow drip can wait, but a bucket under it will not hurt.
Pecan Valley Plumbing
Call Pecan Valley Plumbing, have us call you, or describe the issue.
Prefer to talk?
Call (512) 555-0147